How Do I Place Kitchen Cabinet Skin Pamels

Download Article

Download Commodity

Cabinets are an oft overlooked part of the kitchen, but they can actually make or break the room. Nosotros've all seen kitchens that don't have plenty storage space, but this is a trouble that'southward easy to fix! Build custom cabinets that fit the infinite and spotter how it transforms your kitchen. The room will look more put-together and you lot'll have vital storage for your dishes, pantry, and appliances. Ready to get started? We'll walk you lot through cutting the pieces and assembling them into a classic kitchen cabinet.

1
Cut 2 side panels and 1 lesser panel from plywood. Lay a sail of ^three⁄₄ in (one.9 cm) thick plywood apartment on your piece of work table. Run it through a table saw or use a mitt saw to create 2 evenly sized pieces for the sides of your chiffonier. So, cutting 1 bottom panel that's equal to the width yous want for the whole cabinet, minus ane ¹⁄_ii inches (three.8 cm) for the combined widths of the two side panels.^[1]
- For instance, if you want the kitchen cabinet to be 24 inches (61 cm) wide, subtract 1 ¹⁄₂ inches (iii.viii cm) for the side panels. Your lesser panel piece will be 22 ¹⁄_ii inches (57 cm) wide. You tin brand the side panels equally high as you'd similar your cabinet—anywhere from 30 to 36 inches (76 to 91 cm) is common.
- You lot tin employ solid wood if yous prefer sturdier cabinets. Nonetheless, manufactured woods is cheap and piece of cake to piece of work with.^[ii]
- You might see chiffonier instructions using medium-density fiberboard (MDF), but this isn't equally strong as plywood and so it may not be a good choice if yous're looking to build strong kitchen cabinets.
2
Drill holes onto the side pieces if y'all want to attach adjustable shelves. Lay a side piece downward and identify a shelf pivot drilling jig on the wood. This is essentially a template with holes that are evenly spaced down the side. With the jig in place, take a drill and brand a hole that's at least one ¹⁄₄ in (0.64 cm) broad. For adjustable shelves, make more holes above or beneath the one yous simply fabricated. Repeat the process on the opposite edge of the side piece.^[3]
- Echo this stride for the remaining side piece.
- If you don't desire to make the shelves adjustable, it's fine to simply make a single line of holes for the shelf to sit down on.
Advertisement
3
Cutting a total of 4 support panels that are all the same size. You won't see these, just they'll support your cabinet. Use the same plywood and cut the pieces so they're the aforementioned width every bit your lesser panel. You'll need 2 braces for the meridian of your chiffonier and 2 back up braces for behind the back of the cabinet.
- For instance, if your bottom console is 22 ^one⁄₂ inches (57 cm) wide, your support panels should exist 22 ^one⁄₂ inches (57 cm) as well.
4
Cutting 4 face up panels for a traditional-looking cabinet. You can utilize lumber in any size to make four panels that fit together similar a moving picture frame. For instance, utilise 1x2s, 1x3s, or 1x4s. Proceed in mind that the wider lumber makes more noticeable face frames. You'll be attaching the frame to the front of your cabinet box so they should friction match the meridian and width measurement for your chiffonier.^[4]
- For case, if your chiffonier is 24 by 36 inches (61 cm × 91 cm), you should have 2 long frame pieces that are 36 inches (91 cm) long and 2 short pieces that are effectually 24 inches (61 cm) long—if you're using common measurements.
- If you lot prefer a more modern-looking cabinet, you lot can skip the face panels and install drawers or doors directly onto the cabinet. These are known as frameless cabinets.
5
Cut 1 back panel piece using plywood. Use the same ⁱⁱⁱ⁄_iv in (1.9 cm) plywood and cut the piece to fit the back of your cabinet. It should exist as broad as the cabinet and as loftier as the meridian of your side pieces.^[five]
- So, if your cabinet is 24 by 36 inches (61 cm × 91 cm), you lot need a back panel piece that'southward 24 by 36 inches (61 cm × 91 cm).
- If you're making a wall cabinet, you tin as well cut i acme piece to place on the top of your cabinet. Most people making floor cabinets skip the top piece since they'll be installing countertops instead.
Advert

1
Tack both side pieces to the bottom piece using nails or wood staples. Set 1 of your side pieces upward on your work table and push button the back edge of the bottom slice side by side to it so they form a xc-degree angle. Apply a forest stapler or hammer in nails to temporarily tack the pieces together. And so, repeat this with the other side piece.^[6]
- You tin also ask a friend to help you lot keep the pieces in place as y'all tack them.
- To stop the cabinet box from moving while y'all get together it, clamp a block of forest to your work table. You tin can push the cabinet frame against it to prevent it from sliding while you piece of work.
2
Plough the cabinet onto its top and attach the top bracer to the sides. Carefully flip the cabinet over and then the lesser panel faces up. Then, accept 1 of your top brace pieces and slide it between the side pieces at the front and then it lays flat. Staple or nail the sides to tack the front brace slice in place.
- The meridian brace slice is sometimes called the summit stretcher. It gives support to the cabinet.
3
Nail the back console to the back of your cabinet. Flip the cabinet over so the front end faces down on a flat surface. Then, place the back panel plywood piece on the cabinet so the edges line upwardly perfectly. Nail the back slice to the edges of the cabinet to secure them.^[7]
- If you've got a boom gun, you can speedily attach the dorsum piece to the cabinet. Line upward the nail gun and then the nails go directly into the wood and not into the empty infinite of the cabinet.
four

Adhere the top back brace. Plough the cabinet so the back is flat on your work surface. Take your remaining meridian brace piece and slide it in between the 2 sides so the flat side of the bracer is flush with the back of the cabinet. Then, tack the ends of the bracer to the sides using a wood stapler or nails.^[eight]
5
Tack the support braces behind the back of the cabinet. Flip the cabinet over so the back panel faces upwards. Set 1 support brace on the dorsum console where it meets the bottom and put the other support brace at the pinnacle. And so, staple or nail the ends of the braces to the sides of the cabinet.^[9]
- The support braces add stability so your cabinet doesn't warp. They're too really important if y'all plan on hanging the chiffonier on the wall.
6
Drill screws into the sides of the cabinet to secure the pieces together. Utilise a drill to pre-drill holes along the sides of your cabinet where pieces see. Drill at least 1 pigsty about 1 inch (2.five cm) from the terminate of each slice. Then, go back and drill 1 ⁵⁄₈ in (four.ane cm) wood screws into the holes yous fabricated.^[10]
- Plan on drilling 2 screws onto the side of each brace and 5 screws forth each side of the bottom piece.
Advertisement

1
Apply pegs or corner brackets to support the shelves. Y'all can either push pegs into the holes you lot drilled on the side of the chiffonier and place a shelf straight onto the pegs, or you tin can put the shelf in place and screw in a corner bracket straight underneath the shelf. Echo this for the opposite side of the shelf.^[11]
- Y'all can install purchased shelves or brand your own by cutting a piece of plywood to the width of the cabinet bottom.
ii
Gather the face panels if y'all're using them. Conform the face pieces you cut with narrow lumber so they fit together similar a picture frame—two long parallel strips of woods with 2 horizontal strips that fit between them at the top and bottom. Boom the corners of each piece together so they lay flat. You lot'll fit this unproblematic wooden frame on the front of the cabinet.^[12]
- For an elegant fashion, miter the pieces together instead of pushing them together with a standard butt joint.
iii
Attach the optional confront frame to the front of the chiffonier. With the front of your cabinet facing up, squeeze wood glue onto the elevation sides of your cabinet to provide a little hold. Printing the face frame onto information technology so the frame is even with the sides of the cabinet. And then, hammer in finish nails or use a nail gun to blast the face frame to the chiffonier.^[13]
- To give the frame a polished look, you lot tin fill the nail holes with wood putty.
- Cease nails are slightly wider than standard brad nails. They're sturdier so they'll give the frame more stability.
4
Fit and attach the cabinets in your kitchen. If you're installing the cabinet on the flooring, go it in place and screw directly through the dorsum of the chiffonier into a stud in the wall. To install the cabinet on the wall, get a friend to aid agree the cabinet upward in identify then y'all can drill through the back of the cabinet into the wall studs.^[xiv]
- For extra wall support, install an L-bracket under the bottom of your cabinet. Y'all can notice decorative ones or hide them with a nice backsplash.
- To give your cabinets a professional look, become back and fill the screw holes with putty and let information technology dry before you stain or paint your chiffonier.
5
Buy chiffonier doors and screw them onto your cabinets. Certain, you can make your ain cabinet doors, but it'southward usually more economical to purchase high-quality, professional-looking doors and install them yourself.^[xv]
- Doors are totally optional, especially if y'all're going for an open up, airy look.
Advertisement

Add together New Question

Question

Is it cheaper to build your own cabinets?

Eric Shipe is a Kitchen and Bathroom Designer and the Owner of Bath + Kitchen based in Washington DC. Eric and his squad specialize in cabinetry, blueprint, and remodels. They serve homeowners, interior designers, architects, and contractors with a refined process, creative ideas, 4K photograph-realistic renderings, and 360 Panoramic views. Bathroom + Kitchen was featured in Best of Houzz 2017-2020. Eric holds a BA in Economics and Business Administration from Ursinus Higher.

Dwelling Improvement Specialist

Expert Answer

It always depends on a lot of dissimilar factors such as materials, manufacturer, hardware, and installation.
Question

How do I cull a kitchen cabinet layout?

Eric Shipe is a Kitchen and Bath Designer and the Owner of Bath + Kitchen based in Washington DC. Eric and his squad specialize in cabinetry, design, and remodels. They serve homeowners, interior designers, architects, and contractors with a refined process, artistic ideas, 4K photograph-realistic renderings, and 360 Panoramic views. Bathroom + Kitchen was featured in All-time of Houzz 2017-2020. Eric holds a BA in Economics and Business Administration from Ursinus College.

Home Improvement Specialist

Proficient Answer

Think of usability, ensuring access is comfortable, i.e., doors tin be opened with ease/plenty room. As well anticipate future requirements and provision space for them. If yous program to purchase some appliances or aggrandize your crockery collection in the future, you'll need free space for them.

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Kitchen chiffonier sizes are really variable. They can exist anywhere from 12 to 60 inches (30 to 152 cm) broad and effectually 30 to 36 inches (76 to 91 cm) high.

If you have children at home, consider adding childproof safety features similar locks to your finished cabinets.^[16]

Advertizement

Things You'll Need

Blueprints
³⁄₄ in (one.9 cm) thick plywood
Lumber for face frames
Table or circular saw
Measuring tape
Hammer and nails
Drill
Wood glue
Chiffonier doors and hinges
Screwdriver

*Shelf pin drilling jig

Jigsaw, optional
Smash gun, optional

Well-nigh This Article

Commodity Summary X

To build a kitchen cabinet, start by cut the side and lesser panels out of some MDF or plywood. So, cut 4 panels out of 1 by 6 lumber for the base panels and top bracers, and cut iv more panels for the face of the cabinet. Adjacent, glue and screw the bottom panel to the base panels, and adhere the side panels to the lesser. Once yous've done that, secure the tiptop braces, and nail the back panel onto the chiffonier. Finally, install some shells before assembling the face panels and putting on the doors. To learn how to measure your kitchen cabinet, read on!

Did this summary assist you?

Cheers to all authors for creating a folio that has been read 354,511 times.